Visit Our Adjust-A-Rib Website by clicking on the logo above.   Visit Our Stock Positioning Website by clicking on the logo above.   Visit Our Add-A-Rib Website by clicking on the logo above.
ADD-A-RIB
HOME ABOUT US PRODUCTS PRICE LIST PRODUCT INFO PHOTO GALLERY CONTACT
ADD-A-RIB
 


ADJUST-A-RIB INSTALLATION INSTRUCTIONS


FOR THE BEST RESULTS PLEASE DO THE FOLLOWING

 

CLEANING
Use the enclosed alcohol wiping pads to remove all grease, grit, and grime from the top of your barrel. NOTE: If you do not clean the top of your barrel rib, your Adjust-A-Rib will not stick properly, and eventually work itself loose. Make sure the surface is absolutely clean, and free of grease, fingerprints, and any type of oil. Do not touch the top of the barrel with your hands, especially if you've just changed the oil in your car...3M TAPE doesn't stick to oil or grease of any type.

LEAVING OLD-MID BEAD IN PLACE
If you plan to leave your existing mid-bead in place (and we recommend you do), we suggest you do the following:

  • Leave your Adjust-A-Rib & mounting platform in the closed position (rib is shipped that way)
  • Verify that your Adjust-A-Rib is the correct length you ordered
  • Place the Adjust-A-Rib at the front edge of your rib and it should end just before the beginning of your down ramp of your shotgun rib. If everything is correct, then proceed to do the following:

Before removing the red 3M protective tape from the mounting platform, make sure everything is aligned, then press firmly down so that you make an indentation mark from your existing mid-bead into the bottom of the tape. Then take a battery operated speed control drill, drill through the tape and partially into the rear aluminum surface of the bottom of the mounting platform. (Do not drill thru plate entirely). That will create a pocket for your old mid-bead.

INSTALLATION
Remove the red 3M protective tape exposing the 3M adhesive. Re-align the Adjust-A-Rib and mounting platform to the front of your barrel rib and check the ramp end to see that it does not pass in front of ramp down on your rib. Make sure to align the Adjust-A-Rib mounting platform so that it is equal on both sides of your rib, and that it will be equal all the way down. Then press firmly down (make sure your barrel is lying horizontally, rib up).

CLAMPING
Use 3 plastic clamps large enough so you can clamp the top of the Adjust-A-Rib and the bottom of your barrel. (The clamps can be purchased at Home Depot and Lowe’s). Place each clamp front, middle, & back. For best results leave clamps on for a minimum of 24-36 hours. Make sure the clamps do not tilt the Adjust-A-Rib; make sure the rib is perfectly straight up and down.
Note: Don’t be in a rush. Let the adhesive cure for best results.

REMOVAL
To remove the Adjust-A-Rib and mounting platform, simply use fishing mono-filament 30-40lb test line. Slide the line between your original barrel rib and the bottom of the Adjust-A-Rib mounting platform, moving fishing line side to side (this action will separate the Adjust-A-Rib from the old rib). NOTE: If you left your original mid-bead in place, you will have to stop when the line touches your old mid-bead then start the process all over again from the ramp end of your Adjust-A-Rib mounting platform. Never try to cut the Adjust-A-Rib mounting platform with a razor, or try to pull the rib off your barrel…you will bend and destroy the mounting platform.

If you follow the simple removal instructions, there should never be any damage to the top of the barrel or original rib. If you follow the above steps, your Adjust-A-Rib will never come loose, and your rib will never fall off. A quality installation rests with you. If you have any questions regarding the rib installation (beforebeginning) you can call Ray or Joe at (631) 319-6959 from 9 A.M. – 5 P.M. EST Monday – Friday, and Saturday, from 9 A.M. – 12 P.M. (because once you’ve installed the rib, you cannot move the Adjust-A-Rib back and forth, or side to side).

Remember, if you make a mistake, 3M tape is always available.

Hope your scores jump, and have fun.

Good Shooting

Ray & Joe

         
         
         
 
Braun Professional Stock Positioning Systems
www.Adjustarib.com www.StockPositioning.com www.Addarib.com
 
Copyright © 2012 Add-A-Rib Stock Positioning Systems Adjust-A-Rib Mini-16 Adjust-A-Rib
Stock Positioning, Add-A-Rib, Adjust-A-Rib & Mini-16 Adjust-A-Rib are registered trademarks of Braun Professional Group
All of Our Products are Manufactured in the United States
Site Design by GGI 516.457.9329